Advantech MMP3-21 Bedienungsanleitung Seite 63
- Seite / 112
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Advantech SOM-Express Design Guide
Chapter 5 Carrier Board Design Guidelines 63
Figure 5-26 IDE0 Connections
5.6.2.4 CompactFlash Socket Implementation Notes
The CompactFlash (CF) card cannot be hot-plugged (changed while the system is
powered). If hot-plug support is necessary, then a PCI-based CardBus controller chip
can be integrated onto the carrier board and used to control the CF socket. The CF
card can be configured as a slave device when the CSEL signal is set as non-
connection. If two CF cards (or a CF card and a hard drive) are used in the
master/slave mode on the same IDE port, the IDE_CBLID# pins on both devices
must be connected. These pins negotiate between the master and slave devices.
The devices may not function correctly unless these pins are interconnected.
5.6.3 Layout Guidelines
5.6.3.1 IDE data and strobe routing guideline
This section contains guidelines for connecting and routing the IDE interface. SOM-
Express provides one independent IDE channel. This section provides guidelines for
IDE connector cabling and carrier board design. Additional external 0 # resistors can
be incorporated into the design to address possible noise issues on the carrier board.
If used, these resistors should be placed close to the connector.
The IDE interface can be routed with 6-mil traces on 6-mil spaces (dependent upon
stack-up parameters), and must be less than 10 inches long (from SOM-Express
connector to carrier board IDE connector). Additionally, the maximum length
difference between the data signals and the strobe signal of a channel is 450 mils.
Table 5-18 IDE Routing Summary
Trace Impedance
IDE Routing
requirements
Trace length IDE Signal length matching
55 # ± 15%
6 on 6 (Based
on stack-up in
chap 4)
1 ~ 10 inches
The two strobe signals must be
matched within 100 mils of each other.
The data lines must be within ± 450
mils of the average length of the two
strobe signals
SOM
-
ETX
IDE
_
IOW#
IDE
_
IOR #
IDE
_
A
CK #
IDE
_
CS # 1
IDE
_
CS # 3
IDE
_
A
[ 0 : 2 ]
IDE
_
D[0 : 15 ]
IDE
_
IRQ
IDE
_
IORDY
IDE
_
REQ
IDE
_
CBLID
IDE
Connecto
r
- Advantech 1
- Notices 2
- Revision History 2
- Table of Contents 3
- 4 Table of Contents 4
- Table of Contents 5 5
- 6 Table of Contents 6
- Table of Contents 7 7
- 8 Table of Contents 8
- Chapter 1 Introduction 9
- 1.2 Referenced Documents 10
- 2.1 Overview 11
- 2.2 Specifications 13
- 2.2.1 SOM-5780 14
- 2.2.2 SOM-5782 16
- 2.2.3 SOM-DB5700 18
- 2.3 System Resources 19
- 2.3.1 SOM-5780 Resources 19
- 2.3.2 SOM-5782 Resources 22
- 2.4 PCI Routing 25
- 2.5 DC Specifications 25
- 2.5.1 Interface I/O Voltage 25
- 2.5.1.3 Audio 27
- 2.5.1.4 VGA 27
- 2.5.1.5 LCD 28
- 2.5.1.6 IDE 28
- 2.5.1.7 Ethernet 28
- 2.5.1.8 TV-Out Bus 28
- 2.5.1.9 IrDA 28
- 2.6 AC Specification 29
- 2.6.1 PCI-Bus AC Spec 29
- 2.6.3 Audio AC Spec 29
- 2.6.4 VGA AC Spec 29
- 2.6.5 IDE AC Spec 30
- 2.6.6 I2C AC Spec 30
- 2.6.7 SMBus AC Spec 30
- Chapter 3 Pin Assignments 31
- 3.1 Row A 32
- 3.2 Row B 33
- 3.3 Row C 34
- 3.4 Row D 35
- 4.1 Nominal Board Stack-Up 36
- Thickness 37
- 4.3 Alternate Stack Ups 39
- 5.1 PCI-Bus 40
- 5.1.1 Signal Description 40
- 5.1.2 Design Guidelines 41
- Vtest 0.4 Vcc 1.5 V 42
- Tskew 2 (max) 2 (max) ns 42
- 5.1.3 Layout Guidelines 44
- Carrier 45
- 5.1.4 Application Notes 46
- 5.2.1 Signal Description 47
- 5.2.2 Design Guidelines 47
- 5.2.3 Layout Guideline 48
- SOM-Express 49
- USB Connector 49
- 5.2.3.4 Stubs 50
- 5.3.1 Signal Description 51
- 5.3.2 Design Guidelines 51
- 5.3.2.3 Azalia: 52
- Analog Ground 53
- 5.3.3 Layout Guidelines 54
- ± 15% 54
- 5.4 VGA 56
- 5.4.1 Signal Description 56
- 5.4.2 Design Guidelines 57
- 5.4.3 Layout Guideline 57
- VGA Connector 58
- 5.5 LVDS 59
- 5.5.1 Signal Description 59
- 5.5.2 Design Guideline 59
- 5.5.3 Layout Requirements 60
- 5.6 Primary IDE0 61
- 5.6.1 Signal Description 61
- 5.6.2 Design Guidelines 61
- IDE bus IDE cable 62
- Total Max 62
- Length 13 inches 62
- Carrier Board 62
- 5.6.3 Layout Guidelines 63
- 5.7 Ethernet 64
- 5.7.1 Signal Descriptions 64
- 5.7.2 Design Guidelines 64
- LAN Connector 65
- 5.7.3 Layout Guidelines 66
- 5.7.3.2 Transformer 67
- 5.7.3.3 Critical Dimensions 68
- 5.8 TV-Out 70
- 5.8.1 Signal Descriptions 70
- 5.8.2 Design Guidelines 70
- TV DAC Filter 71
- 5.9 Miscellaneous 72
- Carrier board 74
- 5.10 PCI Express Bus 77
- 5.10.1 Signal Description 77
- Pin Signal I/O Description 77
- 5.10.3.1 Differential pairs 81
- Guidelines 82
- L1 L2 L3 Capacitor Value 83
- L1 L2 Capacitor Value 83
- 5.11 Serial ATA 84
- 5.11.1 Signal Description 84
- 5.11.2 Design Guidelines 84
- 5.11.3 Layout Guidelines 85
- 5.12 LPC 87
- 5.12.1 Signal Description 87
- 5.12.2 Design Guidelines 87
- 5.12.3 Layout Guidelines 87
- 5.12.4 Application Notes 88
- 5.12.4.3 LPT/Floppy 89
- 5.12.4.4 EMI Considerations 89
- Parallel Port 90
- 6.2 Design Guidelines 95
- 8.1 Material of Heatsink 101
- 8.4 Grounding Issues 102
- 8.8.1 Vendor List 106
- 8.8.2 Heat-Spreader 106
- 8.8.3 Heat-Sink 107
- 8.8.4 Thermal Pad 108
- M2.5*6 5 109
- M2.5*16 5 109
- Quantity 109
- 8.8.6 Fan 110
Verwandte Produkte und Handbücher für PC / Workstation Barebones Advantech MMP3-21
Magnetic-products STSS-SAFETY-1.50-2.0-REN podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Ekwipunek Magnetic-products STSS-SAFETY-1.50-2.0-REN.
Dostarczamy 1 pdf podręczników Magnetic-products STSS-SAFETY-1.50-2.0-REN do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Magnetic products STSS-SAFETY-1.50-2.0-REN Instrukcja Użytkownika (2 strony)
Marka: Magnetic-products | Kategoria: Equipment | Rozmiar: 0.20 MB |
Spis treści
Więcej produktów i instrukcji dla Ekwipunek Magnetic-products
| Modele | Rodzaj dokumentu |
|---|---|
| SSEM Series |
Instrukcja Użytkownika
Magnetic Products SSEM Series User Manual,
2 strony
|
| STSS-0505-1.50-2.0-REN |
Instrukcja Użytkownika
Magnetic Products STSS-0505-1.50-2.0-REN User Manual,
2 strony
|
| SSEM-1325 |
Instrukcja Użytkownika
Magnetic Products SSEM-1325 User Manual,
2 strony
|
| SSEM-1320 |
Instrukcja Użytkownika
Magnetic Products SSEM-1320 User Manual,
2 strony
|
| SSEM-1020 |
Instrukcja Użytkownika
Magnetic Products SSEM-1020 User Manual,
2 strony
|
| SSEM-1015 |
Instrukcja Użytkownika
Magnetic Products SSEM-1015 User Manual,
2 strony
|
| SSEM-1010 |
Instrukcja Użytkownika
Magnetic Products SSEM-1010 User Manual,
2 strony
|
| AFM Series |
Instrukcja Użytkownika
Magnetic Products AFM Series User Manual,
2 strony
|
| AFM-0624-REN |
Instrukcja Użytkownika
Magnetic Products AFM-0624-REN User Manual,
2 strony
|
| AFM-0622-REN |
Instrukcja Użytkownika
Magnetic Products AFM-0622-REN User Manual,
2 strony
|
| AFM-0620-REN |
Instrukcja Użytkownika
Magnetic Products AFM-0620-REN User Manual,
2 strony
|
| AFM-0616-REN |
Instrukcja Użytkownika
Magnetic Products AFM-0616-REN User Manual,
2 strony
|
| AFM-0614-REN |
Instrukcja Użytkownika
Magnetic Products AFM-0614-REN User Manual,
2 strony
|
| AFM-0612-REN |
Instrukcja Użytkownika
Magnetic Products AFM-0612-REN User Manual,
2 strony
|
| SS Series |
Instrukcja Użytkownika
Magnetic Products SS Series User Manual,
2 strony
|
| SS-1218 |
Instrukcja Użytkownika
Magnetic Products SS-1218 User Manual,
2 strony
|
| SS-1212 |
Instrukcja Użytkownika
Magnetic Products SS-1212 User Manual,
2 strony
|
| SS-1224 |
Instrukcja Użytkownika
Magnetic Products SS-1224 User Manual,
2 strony
|
| SS-1209 |
Instrukcja Użytkownika
Magnetic Products SS-1209 User Manual,
2 strony
|
| SS-1018 |
Instrukcja Użytkownika
Magnetic Products SS-1018 User Manual,
2 strony
|
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern