Advantech PCI-1242 Bedienungsanleitung PDF herunterladen (Seite 10)

Features

Motion Control I/O Modules

14-10

AMAX-2240 Series

4-axis AMONet

RS-485

Motion Slave Modules

Max. 20 Mbps transfer rate

Max. 6.5 Mhz, 4-Axes pulse output

28 bits counter for incremental encoder

2~4 axes Linear interpolation

2 axes circular interpolation

T-curve and S-curve velocity profiles support

Change speed on-the-fly

Easy installation with RJ45 phone jack and LED diagnostic

Easy installation for servo or stepping motor driver



Speciﬁcations

Pulse Type Motion Control

Motor Driver Support Pulse-type servo

Number of Axes 4

Interpolation Linear or Circular

Max. Output Speed 6.5 Mpps

Step Count Range ± 134,217,728

Pulse Output Type ±OUT/DIR, ±CW/CCW, ±A/B phase

Position Counter ± 134,217,728

Home Modes 13

Velocity Profiles T-curve, S-curve

Local I/O

Machine Interfaces EL+ x 4, EL- x 4, ORG x 4, SD x 4

Servo Driver Interfaces ALM x 4, RDY x 4, SVON x 4, INP x 4, ERC x 4

Position Compare I/O LTC x 4, CMP x 4

Encoder Interface

Input Type AB phase, CW/CCW

Counts per Enc. Cycle x1, x2, x4 (AB phase only)

Input Range Compatible with TIA/EIA-422 Differential Line Driver

I = ±20 mA,VOD = ±2 V/min

Isolation Protection 2,500 Vrms

Max. Input Frequency 2 MHz @ 5 V



General

Bus Type AMONet RS-485

Certifications CE

Connectors RJ45 x 2, SCSI-20P x 8

Dimensions (L x W x H) 125 x 47.6 x 156 mm

Power Consumption 5 W @ 24 V typical

Power Supply Module: 18 ~ 30 V

External: 24 V

± 10%

Humidity 5 ~ 95% RH, non-condensing (IEC 68-2-3)

Operating Temperature 0 ~ 60° C (32 ~ 140° F)

Ordering Information

AMAX-2241/PMA 4-axis AMONet RS-485 Motion Slave Module for

Panasonic Minas A

AMAX-2242/J2S 4-axis AMONet RS-485 Motion Slave Module for

Mitsubishi MR-J2S

AMAX-2243/YS2 4-axis AMONet RS-485 Motion Slave Module for

Yaskawa Sigma-II

PCL-10120M-2 SCSI 20-pin cable, 2 m



Introduction

AMAX-2240 series is used to increase the number of axes for an AMONet™ RS-485 distributed motion control network. These extension slave modules connect serially by a simple

and affordable Cat.5 LAN cable, reducing the wiring between driver and controller. This is very suitable for highly integrated machine automation applications. Please select cable

SCSI-20P and plug this cable into the motor driver and motion slave module.

NEW

AMAX-2242/J2S

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 25 26

Kommentare zu diesen Handbüchern

Keine Kommentare

Advantech PCI-1242 Bedienungsanleitung Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Digitale und analoge E / A-Module Advantech PCI-1242