Advantech RS-100-RT Bedienungsanleitung Seite 20
- Seite / 398
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-10 ADAM 4000 Series User's Manual
Installation Guideline
Changing Baud rate and Checksum
Baud rate and checksum settings have several things in common:
• They should be the same for all modules and host computer.
• Their setting can only be changed by putting a module in the INIT*
state.
• Changed settings can only take effect after a module is rebooted
To alter baud rate or checksum settings you must perform the following
steps:
• Power on all components except the ADAM Module.
• Power the ADAM module on while shorting the INIT* and GND
terminals (See Figure 2-3).
• Wait at least 7 seconds to let self calibration and ranging take effect.
• Configure the checksum status and/or the baud rate.
• Switch the power to the ADAM Module OFF.
• Remove the grounding of the INIT* terminal and power the module on.
• Wait at least 7 seconds to let self calibration and ranging take effect.
• Check the settings (If the baud rate has changed, the settings on the host
computer should be changed accordingly).
Figure 2-3
Grounding the INIT* Terminal
- ADAM 4000 1
- ADAM 4000 Series 3
- Table of Contents 4
- Introduction 7
- 1.1 Overview 8
- Installation Guideline 11
- Power Supply Connections 14
- +10~+30 V 16
- 2.3 Baud rate and Checksum 19
- Grounding the INIT* Terminal 20
- 2.4 Multiple Module Hookup 21
- 2.5 Application Example 22
- Chapter 2 23
- Figure 2-5 23
- I/O Modules 27
- ADAM-4012 Analog Input Module 33
- ADAM-4013 RTD Input Module 34
- Millivolt and Volt Input 35
- Thermocouple Input 35
- Process Current Input 36
- RTD Inputs 37
- Chapter 3 39
- Application Wiring 39
- Strain Gauge Voltage Input 44
- Strain Gauge Current Input 44
- Digital Output used with SSR 45
- Input Modules 46
- ADAM-4017 48
- Figure 3-17 49
- Eight differential 50
- JP9, Jp10 50
- ADAM-4018 51
- ADAM-4018M 52
- Figure 3-20 53
- Figure 3-21 55
- Figure 3-22 55
- Apllication Wiring 55
- T/C or 4~20mA 57
- INPUT RANGE 58
- –0~20 mA 59
- Analog Output 63
- ADAM-4050 Digital I/O Module 65
- DI15 INIT* 68
- INIT*DI15 68
- TTL Input (ADAM-4050) 71
- Figure 3-37 72
- Figure 3-38 72
- Figure 3-39 73
- Figure 3-40 73
- Wet Contact Input (ADAM-4053) 74
- ADAM-4060 Relay Output Module 76
- TYPE SIGNAL 77
- ADAM-4080 82
- ADAM-4080D 83
- Non-isolated Input 84
- Photo-isolated Input 84
- 4.1 Introduction 86
- 4.2 Syntax 86
- ADAM-4011 Command Table 88
- ADAM-4011D Command Table 90
- ADAM-4012 Command Table 92
- ADAM-4013 Command Table 94
- ADAM-4015 Command Table 95
- ADAM-4016 Command Table 96
- ADAM-4017 Command Table 99
- Command Set 100
- ADAM-4017+ Command Set 100
- Chapter 4 101
- ADAM-4018 Command Table 103
- ADAM-4018+ Command Set 104
- ADAM-4018M Command Table 107
- (continued on following page) 107
- ADAM-4019 Command Table 108
- ADAM-4021 Command Table 109
- ADAM-4050 Command Table 110
- ADAM-4052 Command Table 112
- ADAM-4053 Command Table 113
- ADAM-4055 Command Set Table 114
- ADAM-4060/4068 Command Table 115
- ADAM-4080 Command Table 116
- ADAM-4080D Command Table 120
- 76543210 128
- 4015, 4017, 4017+, 4018 138
- 4018+, 4018M, 4019 138
- 4016, 4019 143
- 4011D, 4015 146
- (number of counts) 148
- 4015, 4019 149
- IEC RTD 100O, α = 0.00385 152
- JIS RTD 100O, α = 0.00391 152
- Channel 7 174
- Channel 0 174
- Bit 3 Bit 2 Bit 1 Bit 0 181
- Decimal point 181
- 4011, 4011D, 4012, 4014D 200
- CMD To ADAM4024 231
- Suggest Timing : 231
- T0 : See Table 231
- T1 : 100ms 231
- ADAM-4024 4CH AO Module 232
- %AANNTTCCFF 236
- 01111010 240
- 00001010 240
- 7 6 5 4 3 2 1 0 252
- 4080, 4080D 254
- $AA0L(data) 278
- (ADAM-4080D) 295
- (ADAM-4080) 295
- Calibration 303
- Applying Calibration Voltage 304
- Span Calibration 305
- Zero Calibration 305
- Cold Junction Calibration 306
- Figure 5-5 309
- 5.3 Analog Output Calibration 311
- Technical Specifications 315
- Appendix A 317
- ADAM-4011 Function Diagram 318
- Technical specifications 320
- ADAM-4011D Function Diagram 321
- ADAM-4012 Function Diagram 323
- ADAM-4013 Function Diagram 325
- ADAM-4014D Function Diagram 327
- ADAM-4016 Function Diagram 329
- ADAM-4017 Function Diagram 331
- ADAM-4018 Function Diagram 332
- ADAM-4018M Function Diagram 337
- ADAM-4021 Function Diiagram 339
- ADAM-4050 Function Diagram 341
- ADAM-4052 Function Diagram 343
- ADAM-4053 Function Diagram 345
- ADAM-4060 Function Diagram 347
- ADAM-4080 Function Diagram 349
- LED Display 350
- ADAM-4080D Function Diagram 351
- Data Formats and 353
- I/O Ranges 353
- Data Formats and I/O Ranges 360
- Appendix B 361
- B.3 Analog Output Formats 365
- Technical Diagrams 369
- C.1 ADAM Dimensions 370
- C.2 Installation 371
- DIN-Rail Mounting 372
- C.2.2 Panel Mounting 373
- Appendix C 373
- Figure C-4 373
- Panel Mounting 374
- Piggyback Stack 375
- Utility Software 377
- Main screen 378
- Setup options 379
- Zero Calibration 381
- Terminal Emulation 382
- Operation setting 384
- Alarm setting 384
- RS-485 Network 387
- E.1 Basic Network Layout 388
- Daisychaining 389
- Star structure 389
- Random structure 390
- E. 2 Line Termination 391
- E.3 RS-485 Data Flow Control 394
- How to use the 395
- Checksum feature 395
- F.1 Checksum Enable/Disable 396
Verwandte Produkte und Handbücher für Server Advantech RS-100-RT
Server Advantech RS-400-SF Bedienungsanleitung
(91 Seiten)
(91 Seiten)
Server Advantech EKI-1122L Bedienungsanleitung
(60 Seiten)
(60 Seiten)
Server Advantech EKI-1122L Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Server Advantech RS-200-RT Bedienungsanleitung
(88 Seiten)
(88 Seiten)
Server Advantech RS-100-RT Bedienungsanleitung
(79 Seiten)
(79 Seiten)
Server Advantech EKI-1122L Bedienungsanleitung
(47 Seiten)
(47 Seiten)
Server Advantech EKI-1351 Bedienungsanleitung
(76 Seiten)
(76 Seiten)
Server Advantech PCL-848A/B Spezifikationen
(56 Seiten)
(56 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern