Advantech SBD75e Series Spezifikationen Seite 31
- Seite / 97
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Front Panel Monitoring & Control
Menu Item Operations
Coding:
This will report locked or unlocked.
ALL:
This will report locked or unlocked.
3.3.2.2 Configure
All options selected within this menu are pending settings and will not take effect until the unit is
reconfigured. The settings are only saved when the unit is reconfigured and will be lost if the user
exits out of the configure menu or the unit is power cycled.
The options under this Menu will vary and depend upon the chosen coding scheme; this is stated
in the list below. It is recommended that the entry be done from top to bottom then only
applicable menus will be displayed. The Configure sub-menu may be viewed by selecting the
Configure option from the Select Board menu. The options available are detailed in Table 3.5.
Table 3.5: Configure Sub-menu
Menu Item Operations
Profiles >
Different operational profiles can be saved and loaded via this submenu.
Inputs >
Input selection and LNB control.
Spectrum:
The required spectrum can be set as Normal or Inverted, if known, otherwise
Auto can be used which may increase acquisition time.
Alpha:
The values available for roll-off are: 0.15, 0.20, 0.25, 0.30 and 0.35
Search Range:
The Search range can be set from 0 to 20 MHz. This should be set depending
upon the amount of uncertainty of the carrier.
Search Step:
The Step size of the search can be set from 0 to 500 KHz.
Spectral Analysis:
The setting of this value will be ON, OFF or Auto. If enabled then a FFT will be
performed to aid acquisition.
Coding:
The coding scheme is chosen from a list which is dependant upon the feature
keys that are installed.
3.3.2.2.1 Profiles
The user can store and recall configurations with clear user-definable names. The stored file is
shared by all user interfaces so the GUI could be used to clone a configuration to several units
and the front panel could retrieve this setting. The Profiles sub-menu allows the user to access
these configurations.
Note
The front panel is slightly more restrictive than the GUI due to the limited display and key entry system
but is still easy to use.
To load, delete or create profiles:
1. Select the Profiles option from the Configure sub-menu. The options displayed are detailed
in Table 3.6.
Table 3.6: Profiles Sub-menu
Menu Item Operations
Load Profile >
This option will only be displayed if there are stored profiles.
SBD75e Series Demodulator Installation and Operation Manual
3-5
- SBD75e Series Demodulator 1
- Preface 2
- Copyright Notice 3
- Customer Support 3
- Warranty and Service 4
- Safety Notices 5
- Contents 6
- Who Should Use This Manual 8
- Version Information 8
- RF Interface Options 8
- Summary of Features 9
- Guided Tour 9
- 1.3.2.2 LED Indicators 10
- 1.3.2.3 Keypad 11
- Rear Panel 12
- Typical System Setup 13
- Getting Started 14
- Installation 15
- Introduction 16
- Moving the Equipment Safely 17
- Unpacking 17
- Mechanical Inspection 17
- Installing the Equipment 18
- Cable Routing 19
- Equipment Access 19
- Ventilation 19
- Power Cables 20
- AC Power and Fuse 21
- M&C Connector - RS232 23
- Alarms Connector 24
- RF (L-Band) Input Connector 24
- ASI Output Connector 24
- Demodulator Acquisition Tips 25
- BER Measurement 26
- Overview 29
- Select Board 29
- 3.3.2.1 Status 30
- 3.3.2.1.1 Status 30
- 3.3.2.2 Configure 31
- 3.3.2.2.1 Profiles 31
- 3.3.2.2.2 Inputs 33
- 3.3.2.2.3 Coding 33
- Table 3.9: Coding Options 34
- List of Contents 37
- List of Figures 38
- List of Tables 38
- Safari (Version 2.0) 39
- Opera (Version 9.0) 39
- Accessing the GUI 39
- Overview: Information 40
- Overview: Alarms 40
- Overview: Status 42
- Information 43
- SBD75e: Status 45
- SBD75e: Alarms 46
- General 47
- Output Alarms 48
- Setting Alarms 49
- Setting Warnings 49
- Alarm Status 49
- Play/Pause 50
- Analyzer Pane format 51
- Analyzer Information Icons 51
- 4.7.3.1.2 Cursors 52
- 4.7.3.2.1 Number of Points 53
- 4.7.3.2.2 Persistence 53
- SBD75e: BISS Decryption 58
- BISS Mode Selection 59
- 4.8.2 Off 60
- 4.8.3 BISS-0 60
- 4.8.4 BISS-1 60
- Odd/Even-1 61
- Odd/Even-E 61
- BISS Insertion Period 62
- SBD75e: Configuration 63
- LNB power supply options 64
- PL scrambling seed 64
- Stream Isolation 64
- MODCOD filter 64
- ISI Assignment 64
- 4.9.2.1 Automatic Mode 65
- 4.9.2.3 Manual Mode 68
- 4.9.2.3.1 MODCOD Filter 69
- Advanced 72
- 4.9.3.1 Padding Support 73
- 4.9.3.2 VCM Guard Mode 73
- Profiles 74
- To clone a profile: 76
- Technical Specification 81
- Standards Compliance 84
- Glossary 86
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern