Advantech ACP-7000 Bedienungsanleitung

iACP-700019" RACKMOUNT 7U HEIGHT INDUSTRIAL CHASSISUsers Manual

ACP-7000 User’s Manual 61.6 DimensionsFigure 1.1: DimensionsUnit : mm [inch]

7 Chapter 1 General Information1.7 Exploded DiagramFigure 1.2: Exploded Diagram-1Figure 1.3: Exploded Diagram-2

ACP-7000 User’s Manual 8Figure 1.4: Exploded Diagram 3

9 Chapter 2 System Setup2System Setup CHAPTER

ACP-7000 User’s Manual 10Chapter 2 System Setup2.1 System InstallationWARNING: Before starting the installation process, be sure to shut down all pow

11 Chapter 2 System Setup2.1.3 Chassis Front and Rear SectionsThe front panel switches behind the door are used for system power, sys-tem reset 1, sy

ACP-7000 User’s Manual 12System Reset 1: Press this switch to reinitialize the system. This is the same as the hardware reset button. (Default settin

13 Chapter 2 System SetupThe rear section of B/P version includes B/P rear window, 20-slot I/O brackets and the sheet metal kit for 1+1 or N+1 redund

ACP-7000 User’s Manual 14The SCSI storage holds six 3.5" mobile drawer which is for 1" height SCSI SCA-2 80-pin 3.5" HDD, and with 6-sl

15 Chapter 2 System SetupFigure 2.7: 3.5" Mobile Drawer LatchFigure 2.8: 3.5" Mobile Drawer HandleThe Latch has to be on upper location

ACP-7000 User’s Manual iiCopyright This document is copyrighted, 2

ACP-7000 User’s Manual 162.1.5 CPU Card and Add-on Cards Installationa. Open the top cover and move aside the cardholder by two screwsb. Find out the

17 Chapter 2 System Setup2.1.6 ACP-7000BP-00R, ACP-7000BP-00NACP-7000BP-00R has a momentary switch on the front panel. It is 20-slot backplane versio

ACP-7000 User’s Manual 18Before starting to plug the power cord for ACP-7000BP-57N and ACP-7000BP-81N, be sure both "Inlet" of power cord h

19 Chapter 2 System Setup7000MB-00X; but the mechanical design is for 1+1 redundant power supply. For ACP-7000MB-40Z, sees Figure 2.15, it is with 40

ACP-7000 User’s Manual 202.2 LED Indicators2.2.1 System Status LEDThe System Status LED shows as follows:When the PWR LED is RED, it indicates a redun

21 Chapter 2 System Setup2.2.2 Power Status LEDThe Power Status LED indicates the status of the backplane voltage sig-nals.When a LED fails to light,

ACP-7000 User’s Manual 222.4 Cooling Fan & FilterThere are four (4) Cooling Fans located on the front of the chassis. The cooling fans are very e

23 Chapter 2 System SetupFigure 2.18: System H/S Cooling FansFigure 2.19: SCSI Storage Cooling FansFigure 2.20: Front Door Filter

ACP-7000 User’s Manual 24Figure 2.21: H/S Cooling Fan Filter

25 Chapter 3 Alarm Board3Alarm Board CHAPTER

Table of ContentsiiiContentsChapter 1 General Information ...11.1 Introduction ...

ACP-7000 User’s Manual 26Chapter 3 Alarm BoardThe alarm board is located under the cooling fan section. It gives an audi-ble alarm when:a. Any power

27 Chapter 3 Alarm Board3.2 Alarm board SpecificationInput Power: +5V, +12V Input Signals: • 7 FAN connectors (Pin 1: GND, Pin 2: +12V, Pin 3: FAN Si

ACP-7000 User’s Manual 28CN2 : 10/100M LAN ConnectorPin 1 : SPLED Pin 2 : TERMPLANEPin 3 : RX+ Pin 4 : RX-Pin 5 : GND Pin 6 : LVCCPin 7 : TX+ Pin 8 :

29 Chapter 3 Alarm BoardPin 17 : SPLED Pin 18 : NCPin 19 : LILED Pin 20 : NCPin 21 : GND Pin 22 : NCPin 23 : TX+ Pin 24 : NCPin 25 : TX- Pin 26 : NCP

ACP-7000 User’s Manual 30CN16 : 4 bit Power Good Input,Pin 1 : Power GOOD A Pin 2 : GNDCN17 : Alarm ResetPin 1: Reset Pin 2 : GNDCN18 : LED Board Conn

31 Chapter 3 Alarm Board3.3 Switch SettingTable 1: Fan Number SettingFAN NUM-BERSW1- 1 SW1 - 2 SW1 - 3 SW1 - 41 OFF OFF ON OFF2 OFF ON OFF OFF3 OFF O

ACP-7000 User’s Manual 323.4 Thermal Sensor, LED, USB and K/BThere is a temperature sensor inside the chassis, See Figure 3.2 to find the location and

33 Chapter 3 Alarm BoardThere is a system LED indicator on the front door. See Figure 3.4 for the connection. Pin DefinitionCN1: LED Board ConnectorP

ACP-7000 User’s Manual 34CN1: Internal K/B ConnectorPin 1: KBCK Pin 2: KBDTPin 3: N/C Pin 4: GNDPin 5: KBVCCCN2: Internal USB ConnectorPin 1: US

35 Chapter 4 SCSI StorageChapter 4 Ducks that Need Love!4SCSI StorageCHAPTER

ivFigure 3.1: Alarm Board Layout... 263.2 Alarm board Specification ...

PCM-9575 User’s Manual 36Chapter 4 SCSI Storage4.1 6-slot SCA Backplane LayoutPin DefinitionJ1: On Board Terminator Enable/DisableEnable: Pin 2-3 sh

37 Chapter 4 SCSI Storage4.2 SAF-TEStands for SCSI Accessed Fault-Tolerant Enclosure. The SCA backplane built-in GEM 318 which support SAF-TE provid

PCM-9575 User’s Manual 384.3 RAIDRAID stands for Redundant Array of Independent/Inexpensive Disks. ACP-7000 could be integrated with RAID card, such

1 Chapter 1 General Information1General Information CHAPTER

ACP-7000 User’s Manual 2Chapter 1 Introduction1.1 IntroductionACP-7000 is a high performance, high capacity-computing platform which meets a variety

3 Chapter 1 General InformationOperation Temperature:0°C ~ 40°C (32°F ~ 104°F)Storage Temperature: -40° to +60°C (-40° to +140°F)Relative Humidity: 1

ACP-7000 User’s Manual 41.4 Power Supply OptionsModel nameSpecificationWatt Input Output Mini-load Safety MTBFPS-400ATX-Z400WATX PFC90/264Vac(Full-ra

5 Chapter 1 General Information1.5 System RegulationModel name Specification SafetyACP-7000BP-00R Without backplane, without Power Supply(20-B/P ve